Good advice! We are lucky enough to have a really good plywood distributor nearby as well. If you don’t mind finishing the wood yourself, it’s so much cheaper.
I also get my MDF from them and I love that stuff.
2 Likes
Great point on finishing! I forgot to mention that. I’ve had good luck using this finishing lacquer:
But I also recently tried a cheaper varnish from Krylon that I can find locally and it looks great also. I don’t put any kind of stain on most of my projects.
3 Likes
Do you know what face grade the baltic is? B/BB? B/B? Would you mind posting the exact thickness and face grades? I am trying to figure out if my BB is inconsistent because I am getting different grades… I have some B/B that is at about 0.128", where I am used to more like 0.119" with previous purchases (where I don’t know the grade, but it is likely B/BB).
Just trying to see if there’s a trend on thickness. The B/B stuff is slightly thicker which is a pain to resize my existing models where that matters, but it is cutting super well, I am getting easily 99.5% successful cuts, far more than previous versions where I was seeing around 90%. Maybe luck of the draw, we’ll see.
2 Likes
I honestly don’t know if it’s BB or B grade. It is listed as “Clear Face” and says B/BB. Based on your comments I believe it may be B grade, because it is a tad thicker.
After taking a few measurements with my calipers, the 1/8 inch is right about 3.2mm and the 1/4 is right around 6mm. The stuff I got on Amazon was more like 3mm or even a tad less and doesn’t look as good.
Here is a picture of one side. The other side had maybe 3 plugs. I didn’t notice too many knots, but there are a few tiny ones.
Hope this is helpful.
One other thing. If you are thinking of ordering from them, they replied to my email within 10 minutes the first time I contacted them. So they may be able to give you more accurate info and also can give you a custom quote if needed. They seem to be a very professional shop and well run based on my first visit. They picked and cut my plywood in under 30 minutes.
Ah, Toledo is a bit far, I’m in Atlanta. I go to Rugby architectural building products for my BB, it’s like 3 miles from my house at most. They don’t cut for me like my old supplier did, so it’s a bit awkward to get it home, but it’s a pretty quick process to cut it down once I do.
Man I miss my old supplier, it was nice to come home with a stack of ready-to-go ply.
Rugby is a US national chain, there may be one near lots of you out there:
2 Likes
Since the large pieces of Plywood are usually 48"x 96" if I cut it at 19"I get 5 Pieces which makes 95" plus an inch for saw cuts or error… Then I leave them at the full 48" and cut off what I need at that time which may be 10" or 20" in multiple nested strange shapes, but have used it far more efficiently for cutting it at need.
2 Likes
I just freehand cut one of the 20x50" sheets with a circular saw and did pretty well (cut down to 20x12 ish). I figure I don’t need super accuracy for most of my projects, but I like the idea of keeping a few sheets around uncut so I can make it more efficient later.
Either way, this is definitely going to help me save some margin as I price out some of my designs. Before I was making maybe $10 on a $50 piece, now I’m hoping it will be at least double that after it’s all said and done.
1 Like
I checked Rugby to see if there was one close. Looking at the map it looks like they are repelled by Wisconsin (where I live) 
3 Likes
I was so excited to see the map - looked like CT had one… nope 
You can also check out Ocooch Hardwoods’ scroll saw/laser ready wood. They have a great selection of actual hardwood in varying thicknesses and widths. Ridiculously cheaper than PG hardwood. They also sell a mystery 20 lb off cut/seconds box of domestic hardwood for $25. It’s a bit of a crapshoot what you get, but hey, it’s $25 (plus $13 shipping) .
3 Likes
They were on my list. Definitely seem like a good option and I plan to try them out the next time I need some hardwoods.
1 Like
Here is the result! I cut my new logo on the Baltic birch and the Walnut back. I am happy with the result! The walnut is a bit thinner than Pg. I am also going to try 1/4 inch.
8 Likes
Going to assume you are in or nearby Toledo Ohio as you say that Toledo Plywood is a local company. I’ve had great success with KenCraft Company, an exotic hardwood company in Toledo. Beautiful domestic and exotic woods. They will ship materials to you or you can pick them up in store.
Only downside is that you may need to do some resawing before the material will fit in the 
. They do have some beautiful live edge slabs.
2 Likes
Yes, I buy from Kencraft pretty frequently! I get a lot of my hickory and african mahogany wood from them. Prices don’t seem to be too bad either.
I asked them about Baltic Birch and they said they could cut it, but I never heard back on a price so I just went with Toledo Plywood to try something new. It is nice having both stores so close! Thanks for the reply… Are you local in Toledo now? Saw it had NY in your profile.
1 Like
No still NY. Found out about KenCraft from the “Make Something” Youtube channel. Great content and wonderful guides. He’s a 
user as well.
3 Likes
Ah… cool! He is a pretty well known guy around here, and I think he helps keep them in business 
I haven’t met him personally but I do subscribe to his Youtube channel.
Great for some of you… we live in metro atlanta. Our local options are Home Depot. Oh, and Lowes… Or specialty wood craft stores that make proof-grade look like its cheap. 
2 Likes
When buying plywood, the surface is important, but a lot less important than the interior.
The filler wood is a great place to hide crap quality wood. Lots of holes, etc…
Now, if they chose to leave said holes empty? You’re gonna have flare ups big time.
Alternatively, they may have filled said gaps with glue. Beyond potentially not being laser safe, you’re going to end up with a lot of spots where a cut didn’t actually cut through.
4 Likes
Very true! I’m thinking it’s pretty good quality wood, based on some cutting so far. I am doing a more intricate cut right now and I will see how it goes. This shop does advertise it as good for lasers, so I am hoping it’s good quality plywood inside and out. I haven’t tried shining any light through it to check for voids but I haven’t had any moments yet where I’ve felt the need to.