I say WOW also. What coloring technique did you use?
2 Likes
Would you mind sharing the details on how you did this?
1 Like
Wow. Truly an artist’s take.
1 Like
I just used sharpie markers for the coloring. I colored in each of the areas that I wanted a specific color like I was a three year old (I don’t stay inside the lines very well :)). I gave it a few minutes to dry and then used an alcohol wipe to cleanup the mess. After I’ve colored, it looks like a pre-school art project and then when you start doing the cleanup, the image magically comes to life. Assuming you adjusted the image properly, otherwise you’ll either have lost features because it was too bright or all the features turn into a dark smudge because it wasn’t bright enough! Takes a bit of trial and error to zero it in. I’m still working on that for some of my photos that I want to engrave.
4 Likes
@cditty, I included some above in the thread. The keys to having the picture turn out well are really just trial and error. Getting the source image bright enough but still having good contrast so you don’t lose features is the most important. I have some large test tiles that are 12x12 that I’ll do much smaller test runs with to see if I’m getting the depth & detail that I want with an image. If it doesn’t come out the way I want, back to the photo editor to tweak things. Once I’m happy with it, I’ll put it onto the final tile. For GF settings, I do the engrave at full power, full speed an 450 lines per inch, Gray Scale - Convert to dots, 1 pass. I haven’t tried a lower LPI as I’ve been super happy with the level of detail that 450 gives me.
Getting the multiple colors on some of the tiles can be interesting and tedious. My first tiles were generally just colored black and they wound up giving different shades of gray depending on the depth of the engrave in the image. So instead of just black/white, it gives a nice gradient. My first adventure with color taught me some lessons. If you don’t color in places around where other colors are going to be, when you wipe the color off, it’ll spread into those areas and that’ll be the color it is from then on. If you look at the image above, just to the right of the right arm/horse, the sky is black instead of blue. I hadn’t put the blue on that part yet and when I wiped the Hussar and horse, some of the black went across and filled in that part of the engrave. At that point, I did the rest of the sky so as to not have that problem elsewhere! Once the color is in the engrave, it’s not very easy to change it unless you just soak it in alcohol. I’m still working on my process to keep the ink bleeding to a minimum. Others in the forum are MUCH better at it than I am!
The frame was made using boxes.py. I just created a basic open top box with the dimensions I wanted. I duplicated the holes in the outside of the frame for the front and set the space between them to be just slightly larger than the tile piece so it would be a nice tight fit.
4 Likes
Here’s a few other tiles that I’ve done. I’ve learned quite a bit from each one. None are perfect but I’m happy with the learning process.
After seeing another use post a tile using this image, I just had to have one for myself. My first attempt was ok but then I found a better source image for it and tried again. On this one, I tried doing 2 colors for the first time. Black / Blue. I was pretty happy with it.
There were some related images to the Tie Fighter that I also liked, one being this next image. I tried to get fancy with coloring on this one. Failed miserably but learned quite a bit.
The next one was more just playing around with a wavy-textured tile as well as some random Dr Who content. Artistically, the piece is lacking but it was more just testing out a few things.
This one was another attempt with multiple colors. I got some good depth in the sky but accidentally bled colors into the arm band. Still looks good in person. The image wasn’t really bright enough to highlight all of the detail in the image. This one is going to get a redo later as well.
My favorite so far (other than the Hussar) is this Larry Elmore painting from the Dragonlance world. (No, she didn’t kill him!). The amount of detail that came through on the tile is just amazing. The cape should have been red but my wife stole my red Sharpie and took it to work, so I had to use the purple/magenta one. I’ll probably do another one of these as well, maybe adding some additional color where appropriate.
14 Likes
Incredible!
How are you achieving that water-color sponge-applied look with normal Sharpie markers?!
1 Like
That comes from the alcohol wipes (I’m using the Zeiss wipes because I’ve got a few thousand of them laying around). It tends to mute the colors and gives a bit of a pastel / watercolor type tone to them. If I want a stronger color, I’ll just go over the area another time or two an then be more cautious about how much I’m wiping away.
3 Likes
Thanks. I was mainly wondering about the color process. I want to do multi-colors too but noticed the same thing you said. Once it’s got color, it stays. I was wondering if you did one print or multiple for each color.
I gotta say, those are awesome looking.
1 Like
Thanks! I just did one print. Doing multiple to help isolate the colors would a good way of doing it to ensure you’re not bleeding over but would require a lot more work to isolate those areas in the source image.
All of your tile work is beautiful. And I love the Dr Who frame, did you design that as well?
1 Like
Yes, I did the Dr Who frame as well. That one is just three layers of PG draftboard and the front layer is part of a kitchen cabinet door I got from a Facebook group for free stuff people don’t want. That’s where I got the tiles as well. It was my first attempt at a self standing frame for the tiles. It works ok as long as you get all of the layers glued and aligned perfectly. The tile is very tightly wedged into the middle two layers and then the front layer has a window just slightly smaller than the tile itself. I had done on of the tie-fighter tiles with the same frame but spray painted the frame with a hammered-bronze paint. That looked really nice as well.
1 Like
These tiles are just wonderful! Now I know whom to consult when I decide to do one.
1 Like
Take a look on this thread as well, it’s huge and has an amazing amount of information about tile engraving. Most of the tiles people have posted in that thread make my tiles look positively amateurish. I’m constantly impressed by the level of talent on these forums.
2 Likes
This is excellent! Love the frame too.
1 Like
You should def post a vid of you coloring them! It’d be like watching Bob Ross 
6 Likes
I’ve got a couple of tile projects I’m thinking of doing for some interns at work. Maybe I’ll video up one of those. Just don’t expect me to stay inside of the lines 
2 Likes
@Lotema: These are exquisite!
I’m assuming the alcohol wipes to clean up the bleeding issues with sharpies is immediate, otherwise hard to rub out.
(Starting my GF adventure with tiles but trying to figure out the sharpie bleeding/blending issue)
srdas, I usually give the markers 15-20 minutes to dry before I start wiping with the alcohol wipes.
Best of luck with your adventures in tile! Be sure to post up your results. I still like tiles and want to get back to doing some more with them but some of my other hobbies have been taking up all of my time lately!
1 Like
I find it so fascinating that tiles have come out of nowhere and have become such a versatile (pun intended) medium to showcase many aspects of the Glowforge’s potential. Great example.
4 Likes