What kind of kerf compensation did you use for these? Did you have to glue them?
Every spool I have “springs” apart if I don’t leave a rubber band on it. That means there is always some resistance to it as it feeds. My SD has a rod across the back for hanging spools, but I do have to keep an eye on it which is a pain…
1 Like
I needed a strong work table to put my saw on and had several 18" square tiles. I forgot that the fingers lose a bit when put together but in making a bit of a hang out that did not improve the look but did make it stronger.
12 Likes
Started making these so I can remember what each switch is setup to do on any particular plane.
Perhaps they will get more artful with time but for now they are fully useful.
The backing is cut from foam board and then the graphics are print-and-cut on a polyester mailing label. If the foam board doesn’t hold up I’ll go to Draftboard.
13 Likes
My spice cabinet was looking pretty awful. It is one of those cabinets that has a lot of blind space inside of it that is difficult to access from the door, and there were a lot of spices shoved far back into that no man’s land.
So I started to think about a modular system of bins that could slide easily left-to-right and could be pulled out of the door of the spice cabinet and placed on the counter to be able to pull out the entire spice collection. I measured the doorway with wiggle margin. I was looking for a bin of 7.5 inches wide and 10.5 inches deep, or shallower.
Now, I hate shopping. I hate it with a passion. There was nothing I was less excited about than going to various bin container stores and trying to find just the right sized bins. Until I remembered that I had a Glowforge. This isn’t the thing I normally use my laser for. I normally use it for more decorative and artistic endeavors, but hey, duty calls!
So I went over to the Tray Generator and fired it up and plugged in my dimensions and out popped an SVG file that I later cleaned up and color coded in Inkscape.
Then, tonight, myself, the Glowforge, some packing tape, and a few panels of cardboard from some shipping boxes got busy.
It does what I wanted it to and can fit cleanly in the doorway of the spice cabinet!
And now my spice cabinet looks SO much better!
Now to tackle the tea, coffee, and hot cocoa shelf below the spices and the blender shelf above the spices!
Should you happen to have a spice cabinet of similar dimension, or any other use for this cut file, I’m providing the SVG for you. It was made to work with generic shipping box corrugated cardboard. It isn’t a tight fit so you will need packing tape to hold the panels on. But it does the job, and that is all that matters, practically.
17 Likes
My second ankle surgery is coming up, and I learned the hard way last time that I need easier access to craft stuff to help me cope with the weeks it takes before I can get around well, so I’m squeezing a mini craft area into the bedroom next to my side of the bed. Since my Glowforge won’t fit there, it’s going to be a Cricut craft area. Today I worked on paper storage, and turned out a printer stand and some wall pockets.
24 Likes
Very nice! I really like the open grille.
2 Likes
You are so organized and I especially like the space under your printer. 
3 Likes
Only in that one little corner. Oh, and a small 4-foot area downstairs. 
But it’s a start!
3 Likes
I didn’t want to use a bunch of material on them, so they’re broken down into edge pieces that assemble into the larger rectangles. The slats were another means to material conservation, but I really like the look, too! 
2 Likes
Grab a shoe shelve from Home Depot ($13) and put your cricut on top with a shelf & the tabletop for larger pieces of material you want to stay flat. I did that for the Cricut station at the Makerspace to prevent the sheets from all ending up bent out of shape (including those plastic bottom sheets you stick lightweight stock to in order to cut).
1 Like
The plastic bottom sheets you stick stuff to are hanging on the wall. (I’m pretty sure there’s a name for those, but I can’t think of it right now!)
The Cricut is actually on its own Ikea Lack table underneath the desk. It has just enough space above it to comfortably open the lid and to allow for tools to be stored in the tool holder, but not enough to make the empty space behind it convenient for collecting clutter and interfering with its operation. (Because if there is open horizontal space near my bed when I am laid up, it WILL collect clutter.)
Actually, it will collect clutter even if I am NOT laid up. sigh
4 Likes
I was too but I’m not a Cricutter so am clueless about most of it 
1 Like
I think they’re called cutting mats. What an obscure name, no wonder we couldn’t think of it! 
1 Like
Shouldn’t they be “non-cutting mats” since the idea is your paper gets cut but the mat doesn’t? 
4 Likes
16 Likes
Quicker would be just one wedge? Pushing against 3 faces may hold better, if not so symmetrical?
ooooooohhh, I need to design one for my Kcups!!! Beautiful!!!
Yasssss
